|Brand||AGA Spare Parts|
Baffle Throat Plate
The Baffle Plate is located in the upper region of the firebox, generally above the grate area. It helps to minimise heat loss into the chimney flue by deflecting flames and heat back toward the front of the stove, maximising heat output to the room.
Fire Brick Liners
Fire Bricks are used to line the inside of the stove fire box. They help to insulate the internal sides of the stove from the heat and reflect heat back towards the front of the stove, maximising heat output to the room. There can be made from cast iron, clay or more commonly vermiculite fire board.
Fire Rope Kit
Fire Rope is used to form an air tight seal between the stove door and the stove body to maximise the efficiency and heat output of the stove. A poor seal will allow for additional air to get into the stove fire box increasing the rate of fuel burn and reduce control over the fire burn rate. Rope thickness will vary according to the manufacturer and the size of the stove. Fire Rope is held in place by a High Temperature Rope Adhesive.
Rope Kit contains: 2.5m Fire Rope + Rope End + High Temperature Rope Adhesive.
Stove Glass is a transparent protection front for stoves allowing for a clear view of the fire box. Our high definition [HD] range of Stove Glass is manufactured from the highest quality, high temperature glass ceramic and normally 4mm thick.
Glass Clips & ScrewsReplacement Stove Glass Clips and Screws are designed to safely keep the glass panel in place allowing for an air tight seal to maximise the efficiency and heat output of the stove. Important: Do not over tighten clips and screws as - allow for expansion caused by the heat of the fire when the stove is lit. If the clips are too tight it will crack the glass.
Glass Rope Gasket
The Glass Rope Gasket provides an air tight seal between the glass panel and the metal frame on the stove door. It prevents the glass panel grinding on the metal frame of the stove door when the stove is lit, as the glass expands in the frame.
The Stove Grate is the base on which the fire sits and burns inside the stove firebox. It allows the ashes to fall/riddle down into the ash pan were they can be removed. Multi Fuel Stoves generally have a grate; Wood Burning Stoves generally have no grate. Grates types include: [i] Fixed Grates [ACR Stoves], [ii] Riddle Circular Grate [Aga Stoves] or individual [iii] Grate Bars [Aarrow Stoves.
Stove Glass – Accidental Damage Cover
The Stove Glass Accidental Damage Cover provides insurance for your stove glass for a 12 month or 24 month period. If your Stove Glass accidentally breaks within this period, we will send you a replacement. We do require a photograph to be sent.
The Cover period begins when the stove is dispatched.
Important: The Cover is only for 1 piece of glass, and does not cover the replacement glass.
A Carbon Monoxide Alarm is required to be installed in any room with a Solid Fuel Appliance including Wood Burning Stoves, Multi Fuel Stoves, Pellet Stoves and Gas Stoves. Further guidance on the installation of the carbon monoxide alarm is available in BS EN 50292:2002 and from the alarm manufacturer’s instructions
Our 500mm and 1000mm lengths of Stove Pipe are designed to connect the Wood Burning or Multi Fuel Stove to the chimney systems including Flexible Flue Liner, Twin Wall Flue and Clay Pot Chimney Adaptors.
Closure Plate + Rosette
The Closure Plate [Register Plate] is required when installing a stove. It is designed to close the chimney off from the living area, preventing soot, dust and debris falling down the chimney. It helps to reflect heat back to the living area and minimize draughts from the chimney. Our Closure Plate measures 1000mm x 400mm, with a Pre-Cut 125mm [5 inch] or 150mm [6 inch] centre hole to allow the Stove Pipe to pass.
The Rosette is a finishing trim [125mm / 150mm] ] that is installed were the Stove Pipe passes through the Closure Plate.
External Air Kit
The External Air / Outside Air / Direct Air Kit, is a wall vent that can connect directly into the rear of the stove or air duct in the floor that provides air into the stove for combustion. It is an alternative to a standard wall vent. They are important in New Build Homes, New Extensions and well-sealed airtight rooms.
Half Price Fitting Kit
Our Half Price Fitting Kit is available for our range of Wood Burning and Multi Fuel Stoves and provides various options to install your new stove including Stove Pipe, Closure Plate and Carbon Monoxide Alarm.
Flexi Flue Liner Pack
Our Flexi Flue Liner Packs include a Flue Adaptor, Flexible Flue Liner 316 and a Chimney Cowl.
- Flue Adaptor – Connects the top of Stove Pipe to the bottom of the Flexible Flue Liner.
- Flexible Flue – Relevant length and diameter of Grade 316 Flue Liner.
- Chimney Cowl – The top part of the flue pack, designed to regulate draught, act as a bird guard and rain cap.
Our Packs have been designed to help you easily choose the exact length of Flexible Liner required for your property.
2-Blade Stove Fan
The 2-Blade Heat Powered Stove Fan is designed to circulate the warm air around the room. The fan gently and silently moves air from the hot zone around the stove toward the centre of the room, rather than rising to the ceiling, providing a more even distribution of the heat, a greater comfort and less fuel consumption.
The fan is self-powered using heat from the stove to operate. The fan does not require batteries or mains power.
Firewood Starter Bundle
Our Firewood Starter Bundle contains everything you need to light your first fire in your new stove. Each pack contains:
- 1 x Bag Kiln Dried Log with moisture content of less than 20%.
- 1 x Bag Kindling.
- 1 x Pack Fire Lighters.